-
-
-
-
Core Advantage
-
Product
Lifting and transportation machinery system solution provider
CHAINsterGT Variable Frequency Hoisting Ring Chain Hoist
Classification:
Key words:
FAQ
Details
Products
Inquiry
Case
FAQ
Under normal circumstances, it is not allowed. Above 60Hz (there are also modes above 50Hz), with constant voltage, it generally has a constant power characteristic. When the same torque is required at high speeds, attention must be paid to the selection of the motor and inverter capacity.
Power can still be output below 6Hz, but depending on conditions such as motor temperature rise and starting torque, the minimum operating frequency is set around 6Hz. At this point, the motor can output rated torque without causing serious heating issues. The actual output frequency (starting frequency) of the inverter varies by model, ranging from 0.5 to 3Hz.
When the frequency decreases, the voltage is reduced in direct proportion. Since the AC impedance decreases while the DC resistance remains unchanged, this will tend to reduce the starting torque at low speeds. Therefore, at low frequencies, to achieve a certain starting torque, the output voltage should be increased somewhat when V/f is given. This compensation is called enhanced starting. Various methods can be used to achieve this, including automatic methods, selecting V/f modes, or adjusting potentiometers.
When the frequency decreases, the voltage V also decreases proportionally. This issue has been explained in answer 4. The proportional relationship between V and f is predetermined considering the motor characteristics, and several characteristics are usually stored in the controller's storage device (ROM), which can be selected using a switch or a dial.
Using a frequency converter for operation, the frequency and voltage increase correspondingly with the acceleration of the motor, and the starting current is limited to below 150% of the rated current (depending on the model, it can be 125% to 200%). When starting directly with a power frequency supply, the starting current is 6 to 7 times higher, which can cause mechanical and electrical shocks. Using a frequency converter allows for a smooth start (the starting time is extended). The starting current is 1.2 to 1.5 times the rated current, and the starting torque is 70% to 120% of the rated torque; for frequency converters with automatic torque boost function, the starting torque can exceed 100%, allowing for full load starting.
When the frequency decreases (low speed), if the output power remains the same, the current increases, but under the condition of constant torque, the current remains almost unchanged.
The torque of the motor is generated by the interaction between the magnetic flux and the current flowing through the rotor. At the rated frequency, if the voltage is constant and only the frequency is reduced, the magnetic flux becomes too large, the magnetic circuit saturates, and in severe cases, it can burn out the motor. Therefore, the frequency and voltage must change proportionally, meaning that while changing the frequency, the output voltage of the inverter should be controlled to keep the magnetic flux of the motor constant, avoiding weak magnetism and magnetic saturation phenomena. This control method is often used in energy-saving variable frequency drives for fans and pumps.
The main circuit of the inverter can be roughly divided into two categories: the voltage type, which converts the DC of a voltage source into AC, with the filtering of the DC circuit done by capacitors; and the current type, which converts the DC of a current source into AC, with the filtering of the DC circuit done by inductors.
Product Introduction
Product Detailed Introduction:
CHAINsterGT Variable Frequency Lifting Chain Hoist, Maximum Load 2500kg
• Integrated inverter technology
The integrated programmable inverter technology provides a wide range of functions and ensures better operational safety; no extra force is needed during startup.
• Efficient and fast operation
When not loaded, it has a wider and faster lifting speed (ESR function, with double lifting speed when the load is less than 30%) and a slower lifting speed for precise load control.
• Safety and reliability brought by the integrated lifting monitor
Friction clutch, unchanging safety lifespan calculation rule SWP (load spectrum recording), mechanical and electronic overload protection, hook vibration protection (reducing the impact of sudden vibrations)
Advantages: Efficient, cost-effective control, high quality
Design and Production Capabilities:
• Upper hook
• Specially designed sprocket with intermediate teeth and metal guide chain
• Integrated lifting motor HoistMaster4
• Lifting motor overheat protection
• Hand switch with emergency stop, with plug-in connector, IP65 protection level
• Maintenance-free brake pads
• Separate brake rectifier
• Reserved trolley electrical interface
• Insulation class H, protection class IP55
• 40% ED connection continuous rate, 240 electric operations per hour (ISO M5 working level)
• Ambient temperature -10 degrees to 40 degrees
• Epoxy powder coating 70μm
Standard features of the lifting motor HoistMaster4:
• ESR function = faster lifting speed when lightly loaded
• Mechanical and electronic overload protection
• 2-stage up and down lifting limit
• Load vibration protection, reducing the impact of sudden vibrations
• Chain relaxation control
• Friction clutch. Speed deviation detection
• Brake control. Ensures that the brake is released when the motor is running
• SWP calculation
Highly Recommended:http://www.swfkrantechnik.com/cn/products/chain-hoists/chainstergt.html
Previous Page:
Next page:
Online Inquiry
Fill in your phone number and E-mail information, and we will contact you as soon as possible.
Case
Leave your needs here.
Please leave your needs and we will contact you as soon as possible!
Service Hotline
Manufacturing address：intersection of Caibin West Street and Deren Road in Changchun China-Korea (Changchun) International Cooperation Demonstration Zone
Service Address：No.3 Fumin Street, Lvyuan District, Changchun City
Website：www.兴泰起重.中国
www.crane-china.cc
WeChat service number： xingtaiqizhong
Zip Code：130012
Sales Advisory Phone：400-044-6608/13578886608WeChat Synchronization (Mr. Zhang)
After-sales service telephone：18343082566(Mr. Yu)/400-044-6608
Landline：0431-87096377
Fax：0431-87096377
Copyright：Changchun Xingtai Crane Machinery Co.,Ltd